PRODUCTS

Features:

• Excellent chemical, corrosion and abrasion resistance
• High-build, 16-24 mils (400-610 microns) in a single coat (up to 35 mils with force curing)
• Compatible with controlled cathodic protection
• Suitable for use in exposures as referenced in the following specifications:
• Corp of Engineers C-200, C200a
• AWWA C-210 for exterior
• SSPC-Paint 16
• Steel Tank Institute Corrosion Control System STI-P3
• Approved MPI #35

Features:

• Application up to 30 dry mils (750 microns) in a single coat
• Self priming, single-coat capabilities
• Excellent corrosion resistance
• Complies with MIL-C-18480-B and Bureau of Reclamation CA50 specifications

Features:

• Rapid cure
• VOC compliant for most areas
• Good for filling properties on rough and pitted steel
• Fast dry to handle properties

Features:

• Corrosion resistant coating with zinc phosphate corrosion inhibitor
• Good for extended exposure demands
• Heavy-metal free
• VOC compliant for most areas
• Accepts wide range of topcoats

Features:

• Smooth, attractive, semi-gloss finish.
• Direct-to-metal application if desired.
• Good weatherability, gloss and color retention.
• Contains corrosion inhibitor.
• Excellent application characteristics.
• Quick dry to handle times
• Good flexibility
• Impact and abrasion resistant
• VOC-compliant for most areas

Features:

• Non-skid finish
• Direct-to-metal application if desired.
• Good weatherability, gloss and color retention
• Contains corrosion inhibitor
• Excellent application characteristics.
• Quick dry to service times
• Good flexibility
• Impact and abrasion resistant
• VOC-compliant for most areas

Features:

Features:

• Offers excellent corrosion and weathering protection.
• NORSOK Approved for offshore
• Recommended for chemical industry, offshore, power and heavy industry.

Features:

• Excellent performance over inorganic zinc primers
• Superior color and gloss retention
• Single component
• Spray, brush and roll
• Low odor, low VOC
• Very good filling properties for masonry surfaces

Features:

• Single component
• Resistant to flash rusting
• Outstanding corrosion protection
• Low odor, low VOC

Features:

• Multi-purpose interior/exterior coating
• Excellent color and gloss retention
• Single component
• Outstanding corrosion protection
• Low odor, low VOC
• Acceptable for use in USDA facilities

Features:

• Smooth, attractive, high build finish
• Excellent weatherability, gloss and color retention
• Low odor
• Excellent corrosion protection
• Meets most VOC (Volatile Organic Content) regulations
• Excellent resistance to flash rusting
• Outstanding application characteristics
• Dry-fall* properties
• Suitable for use in USDA inspected facilities

Features:

• Outstanding marine exposure resistance (atmospheric, tidal, subsea)
• Excellent resistance to both organic and mineral acids
• Excellent abrasion and impact resistance
• Excellent resistance to bleach solutions and free chlorine
• Outstanding long-term protection

Features:

• Superior abrasion resistance
• Excellent resistance to aerated seawater and various other chemicals
• Excellent immersion performance
• Easy to repair
• VOC compliant to current AIM regulations

Features:

• Excellent abrasion resistance
• Excellent chemical resistance
• Outstanding impermeability
• Single coat, self-priming capabilities
• VOC compliant to current AIM regulations
• Non-skid surface (optional)

Features:

• Exceptional wetting characteristics
• Low stress, highly flexible film
• Very high solids
• Low odor
• User-friendly brush & roller application
• VOC compliant to current AIM regulations

Features:

• Excellent adhesion to prepared steel & concrete surfaces
• Excellent abrasion resistance
• Excellent flexibility; will withstand the expansion and contraction effect encountered in large storage/processing facilities
• Does not require a primer or a topcoat (self-priming)
• Designed for application using plural component, airless spray equipment
• Versatile Application with both Plural Component or Standard Airless Spray Equipment
• May be applied via batch mixing with care

Features:

• Surface tolerant properties
• Excellent as a ballast tank lining
• Fast and low-temperature cure
• Excellent general service epoxy
• Excellent maintenance primer

Features:

• High abrasion resistance
• Surface tolerant properties
• Fast and low-temperature cure
• Outstanding as a heavy duty hull coating for marine

Features:

• Solvent free
• Excellent film strength, abrasion, and impact resistance
• Rapid hardening for quick service
• Easy to mix ratios
• Excellent film build and working properties

Features:

• Epoxy modification improves chemical resistance for wastewater environment
• Water based, low odor
• Can be used if the substrate is saturated surface damp or "SSD"
• Excellent film strength, abrasion, and impact resistance
• Is castable, making it suitable for restoring pump foundations
• Easily topcoated to provide additional chemical resistance or appearance
• Used as a primer by mixing Parts A and B only - no sand, cement or aggregates
• Topcoated with Carboline's lining systems provides protection from H2S or MIC

Features:

• Epoxy modification improves chemical resistance for wastewater environment
• Trace VOC
• Water based, low odor
• Excellent film strength, abrasion, and impact resistance
• Easily topcoated to provide additional chemical resistance or appearance
• Self-priming over concrete
• Aggregate reinforced

Features:

• Laboratory qualified for multiple ISO 12944 atmospheric-corrosivity categories
• Low odor and low VOC
• Available in a variety of rapid tint colors*
• Attractive medium sheen for tank exteriors
• Good chemical resistance
• Used as a primer, intermediate, or finish coat
• Fast cure & dry times
• Can be applied over power tool cleaned surfaces
• VOC compliant to current AIM regulations
• Good abrasion resistance
• Approved MPI #108

Features:

• Low odor and low VOC
• Low temperature cure
• Available in a variety of colors
• ANSI/NSF Std. 61 for potable water tanks 2000 gallons or larger
• ANSI/NSF Std. 61 for water pipes 54" inch ID or larger
• ANSI/NSF Std. 61 for 4" valves
• AWWA D102 Inside System #1 and #2

Features:

• Low temperature cure (20°F)
• Excellent corrosion protection
• Excellent application characteristics
• Fast recoat times
• Moisture tolerance during application
• Continues to cure underwater
• Extended recoat window for atmospheric exposures (6 months for most topcoats)
• Meets IMO Performance Standard for Protective Coatings MSC.215(82): 2006 for sea water ballast tanks

Features:

• Low temperature cure (20°F)
• Excellent corrosion protection
• Excellent application characteristics
• Fast recoat times
• Moisture tolerance during application
• Continues to cure underwater
• Extended recoat window for atmospheric exposures (6 months for most topcoats)
• Low VOC and low HAPs content
• Certified by UL to meet the drinking water criteria of NSF/ANSI/CAN 600
• Meets IMO Performance Standard for Protective Coatings MSC.215(82): 2006 for sea water ballast tanks

Features:

• High solids, low VOC
• High build (16 mils)
• Low temperature cure (20°F)
• Excellent moisture tolerance during application
• Continues to cure underwater
• Fast cure response
• Suitable for use in USDA inspected facilities

Features:

• High solids, low VOC
• High build (20+ mils)
• Low temperature cure (20°F)
• Excellent moisture tolerance during application
• Continues to cure underwater
• Fast cure response
• Excellent physical and barrier properties

Features:

• Easy mix; non settling; 2-component
• Constant agitation not required during installation
• Short sweat-in time; long pot life
• Unique aggregate package for improved nonslip properties
• Dry hard overnight
• Excellent film build properties

Features:

Features:

• Ready to apply after mixing; no sweat-in time or thinning required
• Versatile epoxy for above or below the waterline
• Extended recoat window (6 mos) for immersion applications
• Used as a primer, intermediate, or finish coat
• Power tool cleaned surfaces acceptable for atmospheric exposures
• HAPs value of 0.12 lbs/solid gallon
• NESHAP and VOC compliant

Features:

• Ready to apply after mixing; no sweat-in time or thinning required
• Economical fit for use epoxy
• Available in a variety of rapid tint colors
• Attractive low sheen for tank exteriors
• Used as a primer, intermediate, or finish coat
• Power tool cleaned surfaces acceptable
• Optional low temperature (LT) cure Part B
• VOC compliant to current AIM regulations

Features:

• Excellent chemical resistance
• Surface tolerant characteristics
• Conventional and low-temperature versions
• Self-priming and primer/finish capabilities
• Very good abrasion resistance
• VOC compliant to current AIM regulations
• Suitable for use in USDA inspected facilities
• Intermediate coat for AWWA D102 Outside System #6 and #7
• Approved MPI #98

Features:

• Excellent chemical resistance
• Surface tolerant characteristics for less severe applications
• Low-temperature version: 890 LT GF
• Self-priming and primer/finish capabilities
• Excellent abrasion resistance & hardness
• VOC compliant to current AIM regulations
• Non-skid service with optional fillers

Features:

• Excellent chemical resistance
• Surface tolerant characteristics
• Low-temperature cure formulation
• Self-priming capability
• Very good abrasion resistance
• VOC compliant to current AIM regulations
• Suitable for use in USDA inspected facilities

Features:

• Excellent chemical resistance
• Surface tolerant characteristics for less severe applications
• Conventional and low-temperature versions
• Self-priming and primer/finish capabilities
• Excellent abrasion resistance & hardness
• VOC compliant to current AIM regulations
• Non-skid service with optional fillers

Features:

• Excellent chemical resistance
• Surface tolerant characteristics
• Self-priming and primer/finish capabilities
• Very good abrasion resistance
• VOC compliant to current AIM regulations
• Suitable for use in USDA inspected facilities

Features:

• Excellent film build and edge protection
• VOC compliant to current AIM regulations
• Meets or exceeds all requirements of: ANSI/NSF Std. 61 for potable water tanks*
• AWWA D102 Inside System 1 and 2
• AWWA C210 for use on interior of steel water pipe
• Complies with FDA 21CFR 175.300 criteria for food contact

Features:

• Meets the FDA requirements for 21CFR 175.300 for direct food contact
• Meets the requirements of AWWA C210
• Ultra High solids; Low VOC and HAPs
• Handles deionized water up to 150°F (66°C)
• Ultra low VOC (67 g/l)
• Good chemical resistance
• Excellent thermal shock resistance
• Good abrasion resistance

Features:

• Compatible over tightly adhered rust and old coatings in mild environments.
• Very good abrasion resistance.
• Excellent performance in wet exposures.
• Meets FDA 21 CFR 175.300 criteria for direct food contact.
• Acceptable for incidental food contact surfaces in federally inspected meat and poultry facilities.
• VOC compliant to current AIM regulations.

Features:

• Ready to apply after mixing; no sweat-in time or thinning required.
• Economical fit for use epoxy
• Used as a primer or intermediate coat
• Can be applied over power tool cleaned surfaces
• Wet on wet application at 75 ° F (24 °C) substrate temperature
• Acceptable over iron phosphate preparation

Features:

• Excellent corrosion protection
• Excellent film build and edge protection
• Used as a primer or an intermediate coating
• Good abrasion resistance
• Cures down to 40°F (4°C)
• VOC compliant to current AIM regulations

Features:

• Ready to apply after mixing; no sweat-in time or thinning required.
• Economical fit for use epoxy
• Available in a variety of rapid tint colors
• Attractive low sheen for tank exteriors
• Used as a primer, intermediate, or finish coat
• Power tool cleaned surfaces acceptable
• Optional low temperature (LT) cure Part B
• VOC compliant to current AIM regulations

Features:

• Ready to apply after mixing; no sweat-in time or thinning required.
• Economical fit for use epoxy
• Available in a variety of rapid tint colors
• Attractive low sheen for tank exteriors
• Used as a primer, intermediate, or finish coat
• Power tool cleaned surfaces acceptable
• VOC compliant to current AIM regulations

Features:

• Ready to apply after mixing; no sweat-in time or thinning required.
• Economical fit for use epoxy
• Used as a primer or intermediate coat
• Can be applied over power tool cleaned surfaces
• Micaceous iron oxide (MiO Filler) for additional barrier properties and corrosion resistance: MiO is purchased separately
• Optional low temperature (LT) cure Part B
• VOC compliant to current AIM regulations

Features:

• Immersion- grade epoxy
• High solids, low VOC
• Excellent adhesion
• Excellent flexibility
• Long recoat window

Features:

• Unique formulation with lamellar aluminum flakes for exceptional barrier protection
• Excellent performance over minimal surface preparation of steel substrates
• Suitable as a topcoat for most tightly adhered existing coatings
• Excellent choice for field touch-up of zinc-rich primers and galvanized steel
• Available in a low temperature cure version (Carbomastic 15 FC)
• Suitable for use under insulation on hot surfaces operating up to 300 °F (150 °C)
• VOC compliant to current AIM regulations

Features:

• Unique formulation with lamellar aluminum flakes for exceptional barrier protection
• Excellent performance over minimal surface preparation of steel substrates
• Suitable as a topcoat for most tightly adhered existing coatings
• Excellent choice for field touch-up of zinc-rich primers and galvanized steel
• May be applied at 35°F (2°C) when CM 15 FC's part B is utilized
• Suitable for use under insulation on hot surfaces operating up to 300°F(150°C)
• VOC compliant to current AIM regulations

Features:

• Excellent immersion performance in both fresh and sea water
• Suitable as a rust preventive coating in ballast tanks and hull applications
• Ideal for sub-sea installations, jackets and other areas exposed to sea water
• Can be applied as low as 5°C (40°F)
• Good flexibility
• Very good abrasion resistance
• VOC compliant

Features:

• High solids, low VOC
• Low temperature cure
• Excellent wetting properties
• Excellent surface tolerance
• Excellent moisture tolerance (application)
• Continues to cure underwater
• Fast cure response
• Suitable for immersion service in fresh or salt water after 60 minutes cure @ 75°F

Features:

• Incorporates lamellar aluminum flakes to provide exceptional barrier protection
• High solids, low VOC
• Low temperature cure
• Excellent wetting properties
• Excellent surface tolerance
• Excellent moisture tolerance after application
• Fast cure response
• Excellent choice for field touch-up of zinc-rich primers and galvanized steel
• Suitable for immersion service in fresh or salt water after 2 hour cure @ 75°F

Features:

• Very good performance over minimal surface preparation of steel substrates
• Suitable as a tie-coat/topcoat for most tightly adhered existing coatings
• Excellent film build on edges
• Can be applied at temperatures as low as 40°F
• VOC compliant to current AIM regulations

Features:

• Surface tolerant epoxy mastic
• Excellent corrosion protection
• Low VOC
• Custom colors available via RTS
• Excellent wetting properties and adhesion
• High solids, low stress over existing coatings
• High film build, up to 7 mils DFT per coat
• Class A Flame Spread and Smoke Development
• Excellent durability
• Good flexibility and impact resistance
• Outstanding abrasion resistance
• Good chemical resistance
• Long pot life
• Long maximum re-coat, up to 1 year
• Approved topcoat over many Carboline Fireproofing Materials

Features:

• Outstanding performance properties in both mild and aggressive environments
• High build; suitable for many two-coat systems
• Suitable for application direct to inorganic zincs
• Application by spray, brush or roller
• Indefinite recoatability
• VOC compliant to current AIM regulations

Features:

• Exceeds SSPC Paint 36 specification for a Level 3 urethane
• Outstanding performance properties in both mild and aggressive environments
• High build; suitable for many two-coat systems
• Application by spray, brush or roller
• Indefinite recoatability
• VOC compliant to current AIM regulations
• Low HAPs content

Features:

• Outstanding performance properties in virtually all industrial markets
• High build; suitable for many two coat systems
• High solids formulation allows for improved edge protection
• Suitable for application direct to inorganic and organic zinc primers
• Indefinite recoatability
• VOC compliant to 100 g/l VOC regulations

Features:

• Very good weathering (75% gloss retention after 4000 hours QUV-A exposure)
• Exceeds SSPC-Paint Spec 36; Level 3
• 6 hours dry to handle time
• High gloss appearance
• Brush, roll, or spray application
• Indefinite recoatability
• Minimum 2 hours working time

Features:

• High solids, low VOC content
• Excellent weatherability
• Exceeds SSPC Paint 36 specification for a Level 3 urethane
• Available in all Carboline colors including metallic-pigmented colors
• Excellent flow characteristics allow for application by spray or roller
• Superior impact and abrasion resistance
• Indefinite recoatability
• VOC compliant to current AIM regulations
• Meets the requirements of AWWA D 102 Outside Coating System (OCS) 5 & 6
• Suitable for use in USDA inspected facilities
• Meets the performance requirements of MIL-PRF-85285E Type II, Class H Polyurethane
• Meets the performance requirements of UFGS 09 97 13.27 Polyurethane Topcoat

Features:

• Excellent weatherability
• Excellent flexibility
• Excellent abrasion resistance
• Available in Carboline’s Rapid Tint System
• Meets most VOC requirements
• Indefinite recoatability

Features:

• Very good weathering (75% gloss retention after 4000 hours QUV-A exposure)
• Exceeds SSPC-Paint Spec 36; Level 3
• 6 hours dry to handle time
• High gloss appearance
• Brush, roll, or spray application
• Minimum 2 hours working time

Features:

• High solids, low VOC content
• Excellent weatherability
• Exceeds SSPC Paint 36 specification for a Level 3 urethane
• Excellent flow characteristics allow for application by spray or roller
• Superior impact and abrasion resistance
• Indefinite recoatability
• VOC compliant to current AIM regulations
• Meets the requirements of AWWA D 102 Outside Coating Systems (OCS) 5 & 6
• Suitable for use in USDA inspected facilities

Features:

• Low VOC – 2.8 pounds per gallon as supplied
• Low HAPS
• Direct-To-Metal (DTM)
• Very Fast Dry – 90-120 minutes to handle at 75°F (24°C)
• High build, high gloss
• Application by conventional or airless spray, HVLP, Electrostatic or plural component spray
• Ambient air or force cure with conventional or infrared ovens
• Meets ISO 12944 C3 Medium

Features:

• VOC compliant – 1.9 lbs/gal (228 g/l) as supplied
• Direct-To-Metal (DTM)
• 6 hours to handle at 75 °F (24 °C)
• High solids, high build, high gloss
• Excellent abrasion resistance
• Application by conventional, airless spray, HVLP or electrostatic
• Excellent chemical resistance
• Ambient air or force cure with conventional or infrared ovens
• Suitable for USDA inspected facilities

Features:

• Excellent thin-film insulation
• Unique formula provides superior coverage during application
• Protects personnel from hot surfaces
• Multi-purpose interior/exterior coating
• Insulation provides anti-condensation properties
• Easy to use
• Zero VOC; Low odor
• May be applied to hot surfaces

Features:

• Excellent thin-film insulation
• Unique epoxy formula outperforms acrylic-based materials
• Tougher and more durable than acrylic coatings
• Higher chemical resistance than acrylic coatings
• Topcoats are optional
• Protects personnel from hot surfaces
• Ideal for industrial/aggressive applications
• Insulation provides anti-condensation properties
• Acceptable for use in USDA facilities
• High film build per coat; fewer coats
• Low VOC; low odor
• May be applied to hot surfaces

Features:

• Provides total submersion and splash and spill cryogenic protection
• Resistant to moisture and chemical exposure
• Excellent spray properties
• Can be applied by plural component airless spray, trowel or casting
• High film build

Features:

• Welds made over Carboweld 11 coated steel are equal in every respect to welds made to uncoated steel
• Designed to protect steel during construction phase of projects under normal conditions
• Can be topcoated for additional long-term protection for atmospheric exposures.
• Weld spatter does not adhere to or damage the coating
• Can be welded as quickly and easily as bare steel at production line speeds without loss in strength or consistency of the weld
• Dries to touch and to handle in 3 to 5 minutes
• Certified as a pre-construction primer for Lloyds Register constructions

Features:

• Contain no VOC's
• Resists harsh chemical exposures
• Will not crack or harden over time
• Application in any weather
• Provides an impermeable protective layer
• No special tools required for application
• Complies with AWWA C217 specification
• Provides excellent protection against chemical splash or fume attack
• Tensile Strength: 45 lbs/in
• Water Vapor Permeability: 0.12 g/m2 per 24 hours
• Service Temperature: 131 °F (55 °C)

Features:

• Isocyanate free
• Exceptional weatherability
• Outstanding color and gloss retention
• Exceeds SSPC Coating Specification No. 36 Level 3A
• Excellent corrosion protection
• Meets ISO 12944 C3 High and C4 Medium, one coat applied at 5 to 7 mils DFT
• High build, 3 to 7 mils DFT
• Saves significant time, labor, and money
• Long service life
• VOC compliant
• Excellent durability
• Good flexibility and abrasion resistance
• Long pot life

Features:

• Isocyanate free
• Exceptional weatherability
• Outstanding color and gloss retention
• Exceeds SSPC Coating Specification No. 36 Level 3A
• Excellent corrosion protection
• Meets ISO 12944 C3 High and C4 Medium, one coat at 5 to 7 mils DFT
• High build, 3 to 7 mils DFT
• Saves significant time, labor, and money
• Long service life
• VOC compliant
• Excellent durability
• Good flexibility and abrasion resistance
• Class A Flame Spread (ASTM E84)
• Long pot life

Features:

• Meets Class B slip co-efficient and creep testing criteria for use on faying surfaces.
• Rapid cure. Dry to handle in 45 minutes at 60°F (16°C) and 50% relative humidity
• Low temperature cure down to 0°F (-18°C)
• High zinc loading
• Meets FDA requirements
• Zinc supplied meets ASTM D520 (Type II)*
• Meets SSPC Paint 20 Type I, Level 1 for zinc content
• Very good resistance to salting
• May be applied with standard airless or conventional spray equipment
• VOC compliant in many areas
• Approved MPI #19

Features:

• Meets Class B slip co-efficient and creep testing criteria for use on faying surfaces.
• Rapid cure.Dry to handle in 30 minutes at 75°F (24°C) and 60% RH
• Can be topcoated in 4-5 hours at 75°F/24°C and minimum 60% RH
• High zinc loading
• Tolerant to mudcracking (up to 6 mils/150 microns)
• Smooth uniform texture reduces topcoat bubbling
• Meets FDA requirements in gray color
• Very good resistance to salting
• May be applied with standard airless or conventional spray equipment
• Low HAPs content of 0.12 lbs/solid gallon

Features:

• Rapid cure. Dry to handle in 45 minutes at 60°F (16°C) and 50% relative humidity.
• Low temperature cure down to 0°F (-18°C).
• Meets FDA requirements in gray color.
• Available in ASTM D520, Type II zinc version.
• Very good resistance to salting.
• May be applied with standard airless or conventional spray equipment.
• VOC compliant in certain areas
• Lower zinc loading for economics.
• VOC compliant for shop/fabricator use only.

Features:

• Meets Class B slip co-efficient and creep testing criteria for use on faying surfaces
• Rapid cure. Dry to handle in 1 hour at 75°F (24°C) and 50% relative humidity
• Low temperature cure down to 15°F (-9°C)
• High zinc loading
• Very good resistance to salting
• May be applied with airless or conventional spray
• Excellent as a lining for solvent storage
• May be used as a weldable pre-construction primer
• Exhibits long-term corrosion resistance
• Low VOC level for solvent-based inorganic zincs

Features:

• Meets Class B slip co-efficient and creep testing criteria for use on faying surfaces.
• Rapid cure. Dry to handle in 1 hour at 75°F (24°C) and 50% relative humidity.
• Low temperature cure down to 0°F (-18°C).
• High zinc loading.
• Approved for MPI #19.
• Meets FDA requirements.
• Zinc supplied meets ASTM D520, Type II.*
• Meets SSPC Paint 20 Type I, Level 1 for zinc content.
• Very good resistance to salting.
• May be applied with standard airless or conventional spray equipment.
• VOC compliant in most areas.

Features:

• Excellent corrosion protection
• High zinc loading per square foot
• Zero VOC
• Good resistance to salting
• Fast curing, quick handling
• Weldable version available Carboweld 11 WB
• Excellent application characteristics (less likely to pump packing or tip plug)
• Meets Class B slip coefficient and creep testing criteria for use on faying surfaces.

Features:

• Rapid cure. Dry to recoat in 90 minutes at 75°F (24°C) and 50% relative humidity.
• Low temperature cure down to 35°F (2°C)
• Meets Class A slip co-efficient and creep testing criteria for use on faying surfaces
• Excellent adhesion
• Protects against undercutting corrosion
• Supplied as ASTM D520, Type II zinc
• VOC compliant to current AIM regulations

Features:

• Protects steel galvanically
• Outstanding application properties
• Cures at low temperatures down to 35°F(2ºC)
• Tough and abrasion resistant film
• Wide use in severe industrial or marine environments

Features:

• Meets Class B slip co-efficient and creep testing criteria for use on faying surfaces
• Rapid cure. Dry to recoat in 30 minutes at 75°F (24°C) and 50% relative humidity.
• Complies with SSPC Paint 20 (Type II)
• Low temperature cure down to 35°F (2°C)
• Excellent adhesion
• Protects against undercutting corrosion
• Field proven primer that applies well by spray methods
• Excellent touch-up primer by brush or roll for small areas.
• VOC compliant to current AIM regulations
• Approved for MPI #20

Features:

• Excellent application properties
• Tough abrasion resistant film
• Excellent adhesion & undercutting resistance
• Superior corrosion resistance
• Meets VOC (Volatile Organic Content) regulations
• Fast drying for quick recoating

Features:

• Provides long-term, fuel efficient protection
• VOC compliant
• Fast dry, high production application characteristics
• Indefinite maximum recoat interval
• Compatible with a wide range of antifoulings

Features:

• Resistant to wind-driven rain in two coats per Federal Specification TT-C-555B
• Over 400% elongation
• Chalk resistant, color retentive
• Contains mildewcide
• Stain resistant
• Breathable
• Easy to clean
• Low odor, low VOC

Features:

Features:

• Single component
• Low odor, low VOC
• Contains no heavy metals or mineral acids
• Extended recoat time
• Accepts two-component solvented coatings
• Fast dry to topcoat
• Approved MPI #134

Features:

• Excellent durability
• Excellent non-reactive, chemical resistant filler
• Improves internal film strength
• Improves impact resistance
• Added as a separate filler as needed

Features:

• Excellent resistance to ethanol, gasoline, jet fuels and solvents.
• Excellent abrasion resistance.
• Excellent thermal shock resistance (0 to 300° F).
• VOC compliant to current AIM regulations.
• Excellent resistance to deionized or demineralized water up to 203°F (95°C).
• Excellent resistance to crude oil up to 250°F (121°C).
• Excellent for crude oil storage and transportation up to 250° F (121° C)
• Recommended for CS-1,3,4 and SS-1,2,3 systems of NACE SP0198 Standard Practice for coatings to control Corrosion Under Insulation (CUI).

Features:

• Excellent solvent/fuel resistance
• Excellent water resistance
• High solids, low odor, low VOC
• Airless spray
• Conforms to MIL-PRF-23236B(SH) Type IV, Class 2, Grade B
• For Low Temperature applications 40°F (4.5°C) refer to Phenoline 187 UHS LT Finish

Features:

• Excellent solvent/fuel resistance
• Excellent water resistance
• High solids, low odor, low VOC
• Airless spray
• Conforms to MIL-PRF-23236B(SH) Type IV, Class 2, Grade B
• Low Temperature application and cure 40°F (4.4°C)

Features:

• Excellent solvent/fuel resistance
• Excellent water resistance
• High solids, low odor, low VOC
• Conforms to MIL-PRF-23236B(SH) Type IV, Class 2, Grade B
• High flash point >200°F (93°C)
• Low Temperature application and cure 40°F (4.4°C)

Features:

• Excellent solvent/fuel resistance
• Excellent water resistance
• High solids, low odor, low VOC
• Conforms to MIL-PRF-23236B(SH) Type IV, Class 2, Grade B
• High flash point >200°F (93°C)
• For Low Temperature applications 40°F (4.5°C) refer to Phenoline 187 UHS LT Primer

Features:

• High solids; Low VOC formula
• VOC compliant to current AIM regulations
• Excellent overall chemical resistance
• Excellent for crude-oil storage
• Excellent resistance up to 400°F(204°C)
• Excellent abrasion & thermal shock resistance
• Meets the FDA requirements for 21CFR 175.300 for direct food contact
• Passes EI 1541 jet fuel gum test
• Complies with MIL-PRF-4556F testing

Features:

• Single coat application reduces labor costs
• Ultra-high build capabilities provides a void-free film and excellent edge protection
• Wide chemical resistance to acids, caustics and aliphatic solvents
• Can be mat reinforced where exposure conditions dictate
• Application by airless spray equipment (plural component acceptable but not required)
• VOC compliant to current AIM regulations

Features:

• Rapid cure-to-handle and cure-to-service characteristics
• Low temperature (35°F) cure capabilities
• Single coat application reduces labor costs
• Ultra-high build capabilities provides a void-free film and excellent edge protection
• Wide chemical resistance to acids, caustics and aliphatic solvents
• Exceptional bond strength
• Can be mat reinforced where exposure conditions dictate
• VOC compliant to current AIM regulations

Features:

• Low temperature cure (20°F)
• Excellent blast-hold protection
• Suitable for use over damp concrete
• Excellent application characteristics
• Fast recoat times
• Moisture tolerance during application
• Meets VOC restrictions
• Low HAP’s content
• Certified by UL to meet the drinking water criteria of NSF/ANSI/CAN 600

Features:

• Single coat, high performance protection
• Low to no odor
• Easy to apply by standard equipment
• Excellent chemical resistance
• Fast cure
• Tough abrasion resistant film
• Suitable for potable water use (complies with ANSI/NSF Standard 61) *
• Excellent flexibility
• Excellent corrosion protection
• Impact resistant
• Hi-build application in one coat
• Low temperature cure (35°F)
• * (Valid if manufactured at a certified location.)

Features:

• Outstanding overall chemical resistance
• Dense, highly cross-linked film for superior barrier protection
• Excellent abrasion resistance and toughness
• Well-suited for hydrocarbon exposures
• Low temperature cure version available

Features:

• Outstanding overall chemical resistance
• Dense, highly cross-linked film for superior barrier protection
• Excellent abrasion resistance and toughness
• Well-suited for hydrocarbon exposures
• Cures down to 35°F (2°C)
• Meets NORSOK System 7C Requirements for subsea equipment up to 356°F (180°C)

Features:

• Single coat application reduces labor costs
• Ultra-high build capabilities provides a voidfree film and excellent edge protection
• Resistant to inorganic and organic acids, caustics and most solvents
• Can be mat reinforced where exposure conditions dictate
• Application by airless spray equipment (plural component acceptable but not required)
• VOC compliant to current AIM regulations

Features:

• High solids; Low VOC formula
• VOC compliant to current AIM regulations
• Excellent for crude-oil storage
• Excellent resistance to petroleum products
• Excellent abrasion resistance
• Excellent thermal shock resistance
• Complies with MIL-PRF-4556F testing
• Fully compliant with the EI1541 performance requirements for Aviation Fuel Handling Systems (commonly known as the Jet Fuel Gum Test)

Features:

• Batch mix formulation, single leg airless spray
• High impact resistance
• Superior adhesion to steel
• Excellent resistance to water and salt water
• Resistance to a broad range of fuels
• Passes EI 1541 requirements for internal protective coating systems used in aviation fuel handling systems, including the jet fuel gum test
• Adheres to API 653 inspection and API 652 guidelines for inspection intervals.
• Resistant to hot water up to 180°F (82°C)
• Excellent abrasion resistance and flexibility
• Can be applied down to 35 °F (2 °C)
• Can be applied as a single or multi-coat system
• Non-blushing with a long recoat window
• Low odor

Features:

• Excellent petrochemical resistance (fuels and crude)
• High impact resistance
• Superior adhesion to steel
• Excellent hot water resistance
• Excellent abrasion resistance
• Can be applied as low as 35°F (2°C)
• Tolerates low temperature excursions to 20°F (-7°C) during cure
• Can be applied as a one-coat 20-80 mil system
• Recommended as a petroleum tank bottom lining per API recommended practice 652.
• Tank Shield Plus is a thick film reinforced lining proven to provide integrity at greater than 50 mils
• Non-blushing, single or multi-coat system
• Recommended as a petroleum tank bottom lining per API recommended practice 653.

Features:

• Non-corrosive to steel embedments
• Reduces job delays
• Economical and easy to use
• Increases strength at early ages.

Features:

• Superior resistance to acids and solvents
• Conforms to many of the current VOC regulations
• Meets the requirements of the U.S. Food and Drug Administration, 21 CFR 175.300 for use in direct food contact areas.

Features:

Features:

• Outstanding resistance to aggressive chemicals
• Suitable for use as a highly chemically resistant lining
• Excellent for splash, spill and film exposures on structural steel
• Glass-flake reinforced film
• High tensile and flexural strength
• High film thickness

Features:

• Outstanding acid immersion performance
• Solvent immersion lining
• High temperature resistance
• Performs under thermal shock
• Extremely high abrasion resistance
• self priming
• High build

Features:

• Quick walk on time
• Fast return to service
• Excellent edge retention
• Superior adhesion to steel
• Resistance to a broad range of chemicals
• Will cure down to 20°F/-7°C
• Can be applied as a single-coat 20-60 mil system
• Passes EI 1541 jet fuel gum test.

Features:

• High impact resistance
• Superior adhesion to steel and concrete
• Resistance to a broad range of chemicals
• Can be applied in a one-coat application up to 60 mils
• Can be sprayed using single component airless equipment
• VOC compliant
• Passes ASTM G210 - Severe Wastewater Analysis Tests (SWAT)
• Certified by UL to meet the drinking water criteria of NSF 61
• Certified by UL to meet the drinking water criteria of NSF/ANSI/CAN 600

Features:

• High Impact Resistance
• Superior adhesion to metal substrates and concrete
• Outstanding adhesion to stainless steel, even with low blast profiles
• Well suited to protect alloy steels typically used to wet FGD systems where pitting and crevice corrosion often occur
• Fast cure-to-service; depending upon application can be placed into service within 36 hours
• Minimal blushing characteristics
• Can be applied in temperatures as low as 35 °F (1.7 °C)
• Can be applied as a one-coat system
• Tested and approved for crude oil transportation up to 350 °F (177 °C)
• Superior thermal shock resistance from -40 to 350 °F (-40-177 °C)
• Complies with the API RP 652 definition of a reinforced liner.

Features:

• High impact and thermal shock resistance
• Superior adhesion to steel and concrete
• Resistance to a broad range of chemicals
• Can be applied up to 60 mils in one coat
• Can be sprayed using single component airless equipment
• Passes ASTM G210 - Severe Waste Water Analysis Test (SWAT)

Features:

• Versatile coating with wide chemical resistance
• Excellent abrasion resistance
• Excellent thermal shock resistance
• Excellent resistance to fuels
• Long history of performance
• Self-priming

Features:

• Versatile coating with wide chemical resistance
• Outstanding abrasion resistance
• Excellent thermal shock resistance
• Excellent resistance to fuels
• Long history of performance
• Self-priming

Features:

• Versatile coating with wide chemical resistance
• Excellent abrasion resistance
• Excellent thermal shock resistance
• Excellent resistance to fuels
• Long history of performance
• Self-priming

Features:

• Excellent overall chemical resistance to a wide range of acids, alkalies and solvents.
• Superior abrasion resistance and good flexibility
• Complies with FDA 21CFR 175.300 criteria for food contact

Features:

• Excellent overall chemical resistance to a wide range of acids, alkalies and solvents.
• Very good abrasion resistance and flexibility
• Complies with FDA 21CFR 175.300 criteria for food contact

Features:

• Excellent overall chemical resistance to a wide range of acids, alkalies and solvents.
• Smooth non-stick surface.
• Very good abrasion resistance and flexibility.
• Complies with FDA 21CFR 175.300 criteria for food contact.

Features:

• Easy-to-apply high performance thin film lining
• Protects I high temperature demineralized water immersion - 212°F (100°C)
• Recommended in high pressure three phase service up to 250°F (121°C)
• Can be air dried or force cured for prompt service

Features:

• Easy-to-apply high performance thin film lining
• Protects I high temperature demineralized water immersion - 212°F (100°C)
• Recommended in high pressure three phase service up to 250°F (121°C)
• Can be air dried or force cured for prompt service
• Outstanding abrasion resistance

Features:

Features:

• Primary use is as a tank lining for water
• Applications include deionized or distilled water at elevated temperatures, as well as use with brines, petroleum processes and products
• High solids, Low VOC product
• Excellent chemical resistance to crude oil, alkalis, and other various fuels

Features:

• Excellent overall chemical resistance to a wide range of acids, alkalies and solvents
• Very good abrasion resistance and flexibility
• Complies with FDA 21 CFR 175.300 criteria for food contact

Features:

• Outstanding overall chemical resistance
• Dense, highly cross-linked film for superior barrier protection
• Superior immersion resistance
• Excellent abrasion resistance and toughness
• Well-suited for hydrocarbon exposures
• Formulated for use in a large variety of facilities including waste water, chemical and fuel storage, wet-gas pipelines, rail cars, barges and ship tanks
• Bis A free
• Cures down to 35°F (2°C)

Features:

• Meets FDA requirements for 21CFR 175.300 for Aqueous food contact
• VOC compliant to current AIM regulations
• Excellent for crude-oil storage
• Excellent resistance to petroleum products
• Excellent abrasion resistance
• Excellent thermal shock resistance

Features:

Features:

• Resistant to corrosion caused by MIC and hydrogen sulfide
• Outstanding abrasion and impact resistance
• Fast curing
• Low temperature cure
• Superior wetting properties
• Excellent adhesion to steel and DIP
• Mix ratio of 1:1 and user friendly application properties.
• Unlimited build with single multi-pass coats.
• Self priming
• Meets AWWA C222

Features:

• Fast curing rate increases throughput
• Superior wetting properties result in better edge retention and excellent adhesion to steel
• Mix ratio of 1:1 and user friendly application properties
• Unlimited build with single multi-pass coats
• Self priming (120 mil maximum for potable water)
• Meets AWWA C222
• UL approved for ANSI/NSF Std. 61 potable water

Features:

• Fast curing rate increases throughput
• Excellent abrasion resistance
• Superior wetting properties for outstanding adhesion
• Mix ratio 1:1 and user friendly application properties
• Can be topcoated with Carbothane series of products
• Unlimited build with single multi-pass coats
• Compliant with AWWA C222
• Compliant with EN 10290

Features:

• Rapid curing to increase through put
• Excellent abrasion resistance
• Superior wetting properties for outstanding adhesion
• Robust 1:1 mix ratio and user friendly application properties
• Can be topcoated by Carbothane aliphatic polyurethanes
• Unlimited build with single multi-pass coats
• Compliant with AWWA C222

Features:

• Fast curing increases throughput
• Excellent abrasion resistance
• Superior wetting properties for outstanding adhesion
• Mix ratio of 1:1 with easy application properties
• Can be topcoated with Carbothane series of products
• Unlimited film build with single or multi-pass coats

Features:

• Fast curing increases throughput
• Excellent abrasion resistance
• Superior wetting properties for outstanding adhesion
• Mix ratio 1:1 and user friendly application properties
• Can be topcoated by Carbothane series of products
• Unlimited build with single multi-pass coats
• Compliant with AWWA C222
• Compliant with EN 10290

Features:

• Low temperature cure
• Quick cure to handle
• Superior wetting properties and outstanding adhesion to steel
• Excellent edge retention
• Mix ratio of 1:1 and user friendly application properties
• Up to 80 mils build with a single application
• Can be topcoated with Carbothane series of products for long-term color and gloss retention

Features:

• Improves flow efficiency in gas pipes
• Excellent flow and leveling
• Single-coat application
• Hard, smooth, glossy finish
• Excellent abrasion resistance
• Meets all criteria of API RP 5L2
• Long pot life

Features:

• Improves flow efficiency in gas pipes
• Excellent flow and leveling
• Single-coat application
• Hard, smooth, glossy finish
• Excellent abrasion resistance
• Meets all criteria of API RP 5L2
• Corrosion prevention during storage

Features:

• Improves flow efficiency in gas pipes
• Meets API RP5L2 requirements for gas transmission pipeline flow liner
• Excellent flow and leveling
• Single-coat application
• Hard, smooth, glossy finish
• Excellent abrasion resistance
• Corrosion prevention during storage

Features:

• Quick dry to touch and QC times
• Color indicator confirms proper mixing
• Low temperature cure 40°F (4.4°C)
• Excellent cathodic protection performance
• Film build up to 50 mils DFT in one coat
• Excellent edge retention
• Superior adhesion to steel
• Excellent adhesion over prepared FBE, epoxy and polyurethane coated pipe
• Can be applied by spray, brush, roller or dual cartridge

Features:

• Quick dry to touch and QC times
• Good brush and roll properties
• Color indicator confirms proper mixing
• Low temperature cure 40°F (4.4°C)
• Excellent cathodic protection performance
• Film build up to 30 mils DFT in one coat
• Excellent edge retention
• Superior adhesion to steel
• Excellent adhesion over prepared FBE, epoxy and polyurethane coated pipe
• Can be hand applied by brush or roller

Features:

• Excellent gouge and abrasion resistance
• High crosslink density results in tough film
• Excellent adhesion to prepared FBE, Polyclad 975 and other coatings
• Protects FBE, and other base coats during directional drilling applications
• Zero VOCs, 100% solids
• Apply up to 125 mils (3.2 mm) in one application
• Rapid dry to handle, less than 20 minutes

Features:

• Full jet fire certification in accordance with ISO 22899
• Excellent hydrocarbon pool fire protection (ISO 834/BS-476)
• LR, DNV & ABS certification
• Successfully passed Norsok M-501 System 5A environmental test program without a topcoat
• Superior weathering resistance
• Very low moisture absorption
• Explosion resistance
• Extremely durable, impact resistant finish
• High film build properties
• Low flame spread and smoke development

Features:

• Over 40 years of proven performance
• Exceptional durability and toughness
• UL 1709 hydrocarbon fire rated up to 4 hours
• Jet fire rated up to 2 hours
• ASTM E119 cellulosic fire rated up to 4 hours
• Cryogenic protection against LNG spills and immersion exposures
• Resistant to 3 bar blast overpressure
• Hose stream resistant
• UL 2431 Category I-A Outdoor Heavy Industrial and Exterior Environmental Purpose
• Tolerant to wide range of climates
• Lightweight – one-fifth the weight of concrete for equal fire protection
• Ideal for onsite and offsite application
• Easy application by spray or trowel
• Nonflammable – during or after application
• Chloride and sulfide free – no special priming required
• Asbestos-free – complies with EPA and OSHA regulations
• Non-friable – high impact strength

Features:

• Heavy duty, ultra high density formulation
• Highest durability and toughness on the market
• UL 1709 hydrocarbon fire rated up to 4 hours
• ISO 22899-1 jet fire rated up to 2 hours
• ASTM E119 cellulosic fire rated up to 4 hours
• Cryogenic protection against LNG spills and immersion exposures
• Resistant to 3 bar blast overpressure
• Hose stream resistant
• Tolerant to wide range of climates
• Lightweight – one-fifth the weight of concrete for equal fire protection
• Ideal for onsite and offsite application
• Easy application by spray or trowel
• Nonflammable – during or after application
• Chloride and sulfide free – no special priming required
• Asbestos-free – complies with EPA and OSHA regulations
• Non-friable – high impact strength

Features:

• Cost effective, high yield
• Exceptional durability and toughness
• UL 1709 hydrocarbon fire rated up to 4 hours
• ISO 22899-1 jet fire rated up to 2 hours
• Cryogenic protection against LNG spills and immersion exposures
• Resistant to 3 bar blast overpressure
• Hose stream resistant
• Tolerant to wide range of climates
• Lightweight – one-fifth the weight of concrete for equal fire protection
• Ideal for onsite and offsite application
• Easy application by spray or trowel
• Nonflammable – during or after application
• Chloride and sulfide free – no special priming required
• Asbestos-free – complies with EPA and OSHA regulations
• Non-friable – high impact strength

Features:

• Cost effective fireproofing solution
• Outstanding coverage, high build
• Exceptional durability and toughness
• UL 1709 hydrocarbon fire rated up to 4 hours
• BS 476 hydrocarbon fire rated up to 4 hours
• ISO 22899-1 jet fire rated up to 2 hours
• ASTM E119 cellulosic fire rated up to 4 hours
• Cryogenic protection against LNG spills and immersion exposures
• Resistant to 3 bar blast overpressure
• Hose stream resistant
• Tolerant to wide range of climates
• Lightweight – one-fifth the weight of concrete for equal fire protection
• Easy application by spray or trowel
• Nonflammable – during or after application
• Chloride and sulfide free – no special priming required
• Asbestos-free – complies with EPA and OSHA regulations
• Non-friable – high impact strength

Features:

• UL approved for ANSI/NSF Std. 61 potable water*
• Certified by UL to meet the drinking water criteria of NSF/ANSI/CAN 600
• Complies with 21 CFR 175.300 Method D, E, & G and Direct Dry Food Contact
• Complies with Greenbook
• Passes ASTM G210 - Severe Wastewater Analysis Tests (SWAT)
• Cold temperature cure
• Fast cure and walk on time
• Excellent barrier properties, low permeability
• Single-coat application 60 to 125 mils
• Bridges normal shrinkage cracks in concrete
• True monolithic film on steel and concrete
• Encapsulates rivets, bolts, and edges in one coat
• Outstanding abrasion, impact and tear resistance
• Combines polyurethane and polyurea technologies to form a hybrid polyurethane

Features:

• Universal primer and tie-coat
• Excellent adhesion to SSPC-SP 2 prepared steel, galvanizing, aluminum, stainless steel and copper
• Low stress, highly flexible film
• Extremely high solids
• Low odor
• Contains corrosion inhibitors
• Compatible with a variety of topcoats
• User friendly brush and roller application
• VOC compliant to current AIM regulations

Features:

• Universal primer and tie-coat
• Cures down to 35°F (2°C)
• Excellent adhesion to SSPC-SP 2 prepared steel, galvanizing, aluminum, stainless steel and copper
• Low stress, highly flexible film
• Extremely high solids
• Low odor
• Contains corrosion inhibitors
• Compatible with a variety of topcoats
• User friendly brush and roller application
• VOC compliant to current AIM regulations

Features:

• Excellent primer/sealer for drywall
• Glue-like bond to almost any surface
• Outstanding tie-coat over existing coatings
• Single component, thin-film application
• Topcoat with virtually any generic coating
• Ready-to-apply as supplied
• Fast drying
• Low odor; low VOC
• Suitable for use in USDA inspected facilities

Features:

• Quick return to service (2-4 hours for foot traffic)
• Self-leveling
• Smooth, gloss finish
• Flexible with high impact resistance
• Excellent UV protection
• Excellent chemical and abrasion resistance
• Extended pot-life or working time
• 95% volume solids, low VOC, low odor
• Suitable for use in USDA inspected facilities
• Available in custom colors
• Class A fire rating

Features:

• Outstanding wetting properties
• Solvent-free
• Long working time
• Excellent adhesion
• Compatible with a variety of toppings

Features:

• Excellent resistance to chemical attack
• Excellent abrasion and impact resistance
• Exceptional thermal shock resistance
• Superior bonding properties
• High cohesive strength
• Low permeability
• Low odor

Features:

• Excellent resistance to chemical attack
• Excellent abrasion and impact resistance
• Exceptional thermal shock resistance
• Superior acid resistance
• Superior bonding qualities
• High cohesive strength
• Low permeability
• Low odor

Features:

• Excellent resistance to chemical attack
• Excellent abrasion and impact resistance
• Exceptional thermal shock resistance
• Superior adhesion to both steel or concrete
• High cohesive strength
• Low permeability
• Low odor

Features:

• Excellent resistance to chemical attack
• Excellent abrasion and impact resistance
• Exceptional thermal shock resistance
• Superior bonding qualities
• High cohesive strength
• Low permeability
• Low odor
• Formulated to resist a variety of chemical solutions.

Features:

• Highly Flexible
• Chemical Resistant
• Water Resistant
• Abrasion Resistant
• 100% Solids

Features:

• Designed for underwater and other wet applications
• Can be applied up to 2" in thickness
• Self-priming on most surfaces and over most generic types of coatings
• Rapid cure characteristics
• VOC compliant to current AIM regulations

Features:

• Minimum Toxicity - Waterborne
• Biodegradable

Features:

• Excellent “hot” application characteristics, may be applied over hot substrates up to 300°F (149°C)
• Will air dry “tack free” at ambient but will remain soft until heat curing has been achieved
• Typically topcoated with a silicone or modified silicone finish

Features:

• VOC compliant to 340 g/l
• Tolerant of power tool cleaned surfaces
• Zinc filler provides excellent corrosion and undercuttung resistance
• May be applied over hot substrates up to 150°F (65°C)
• Will air dry “tack free” at ambient but will remain soft until heat curing has been achieved
• Typically topcoated with a silicone or modified silicone finish

Features:

• Inorganic; stable; inert polymer
• Outstanding durability
• Excellent corrosion protection (used over Carbozinc inorganic primers)
• High temperature resistance (800 °F [426 °C])
• VOC compliant
• Cures at ambient conditions (hard in 2 hours)
• Cures down to 40 °F (4 °C)
• Does not require heat cure for high-temp service
• Outstanding resistance to handling damage
• Single-package

Features:

• Temperature resistance up to 450 °F (232 °C)
• High-build single-coat capabilities
• Excellent resistance to thermal shock
• Superior abrasion and chemical resistance
• Glass flake reinforcement
• Ambient-temperature cure
• VOC compliant to current AIM regulations

Features:

• Versatile use from cryogenic to 400°F (204°C) exposures
• Very good flexibility
• Excellent overall chemical resistance
• Very good abrasion resistance
• Easily applied by spray
• Acceptable for use over stainless steels
• High solids, low VOC formula

Features:

• Resistant to severe thermal shock
• Provides outstanding long-term performance when applied over Carbozinc inorganic zinc primers
• Provides barrier protection prior to heat curing (full film physical properties occur after heat curing)

Features:

• Resistant to severe thermal shock
• Provides outstanding long-term performance when applied over Carbozinc inorganic zinc primers
• Provides barrier protection prior to heat curing (full film physical properties occur after heat curing)
• Approved MPI #22

Features:

• Resistant to severe thermal shock
• Provides outstanding long-term performance when applied over Carbozinc inorganic zinc primers
• Provides barrier protection prior to heat curing (full film physical properties occur after heat curing)
• VOC compliant

Features:

• Resistant to severe thermal shock
• Provides outstanding long-term performance when applied over Carbozinc inorganic zinc primers
• Provides barrier protection prior to heat curing (full film physical properties occur after heat curing)
• VOC compliant
• Approved MPI #22

Features:

• Zinc rich formulation provides outstanding corrosion resistance
• Air dries to touch at ambient temperatures
• Is resistant to severe thermal shock
• Provides outstanding long-term performance and appearance when topcoated with Thermaline Silicone Finishes

Features:

• 450°F (232°C) Temperature resistance
• Single-coat application
• Excellent resistance to thermal shock
• Good weathering and color stability

Features:

• Temperature resistance up to 525°F (273°C)
• Single-coat application
• Excellent resistance to thermal shock
• Good weathering and color stability

Features:

• Temperature resistance up to 500°F (260°C)
• Single-coat application
• Excellent resistance to thermal shock
• Good weathering and color stability
• VOC compliant
• RTS colors available

Features:

• Unique reinforced but flexible polymer film
• Versatile use from cryogenic to 1200°F (650°C) exposures
• Dries to handle without heat cure (See curing schedule)
• Outstanding barrier properties
• Protects steel from thermal wet cyclic conditions
• Suitable for both shop and field application
• Provides corrosion protection even with ambient temperature cure
• Meets ISO 12944-6 C5-M Medium
• Self priming or apply over Carbozinc 11 primers when uninsulated
• Protects stainless steels from chlorides and stress corrosion cracking
• Very fast recoat times

Features:

• Flexible
• Hard, dust free surface
• Allows easy replacement of cables
• Water-based product, low odor
• Asbestos-Free – complies with EPA and OSHA regulations
• Factory Mutual – tested and approved
• Does not de-rate cables
• Weathering – approved for exterior use
• Quality Manufactured – under strict Carboline quality standards
• Provides protection at 1/16” Dry Film Thickness

Features:

• Provides a flexible fire protection solution to structural steelwork, process vessels, divisions and electrical raceways for 1 through 4 hours.
• Lowest thickness per fire rating of any competitive epoxy intumescent coating.
• Inherently flexible and durable formulation designed to withstand abrasion, vibration, handling, transportation and erection stresses in any climate.
• Formulated to maintain it’s flexibility, elongation and fire resistive properties throughout its service life regardless of climate.
• Engineered to resist extreme and rapid temperature cycles without cracking or disbondment.
• Extensive outgas testing for controlled cleanroom and sterile environments.

Features:

• Provides a flexible fire protection solution to structural steelwork, process vessels, divisions and electrical raceways for 1 through 4 hours.
• Lowest thickness per fire rating of any competitive epoxy intumescent coating.
• Inherently flexible and durable formulation designed to withstand abrasion, vibration, handling, transportation and erection stresses in any climate.
• Formulated to maintain it’s flexibility, elongation and fire resistive properties throughout its service life regardless of climate.
• Engineered to resist extreme and rapid temperature cycles without cracking or disbondment.
• Extensive outgas testing for controlled cleanroom and sterile environments.